solar tracker with hydraulic control units

Solar tracking is one of the most effective ways to increase the productivity of a
photovoltaic plant. By orienting modules toward the sun throughout the day, single-axis
and dual-axis trackers can raise energy yield by 15 to 45% compared to fixed-tilt
installations. Behind this performance gain lies a demanding motion-control problem:
moving large, heavy structures with accuracy, holding position against wind loads, and
reacting instantly when a storm approaches. This is exactly where the hydraulic power
unit (HPU) for suntracking proves to be a cross-cutting, high-value solution.

In this article we look at why hydraulics is so well suited to solar tracking, and how an
intelligent Smart Power Unit can read panel sensors and control position in closed loop,
driving up to six photovoltaic panels from a single compact unit.

Why hydraulic power unit for solar tracking

Solar trackers operate outdoors, often in harsh desert or coastal environments, under wide temperature swings, dust, humidity and salt. They must move slowly and precisely during the day, then lock firmly in position, and finally react fast when wind conditions demand a protective stow position. Few actuation technologies combine all of these requirements as effectively as hydraulics.

High torque density. A compact hydraulic power unit delivers very high force from a small footprint. This is decisive when moving large single-axis rows or heavy dual-axis structures and heliostats, especially against the bending and torsional loads generated by wind.

Position holding without continuous energy draw. Once the array reaches the target angle, hydraulic locking through pilot-operated check valves keeps it fixed without the motor running. The pump activates only to correct position, which improves the overall energy balance of the plant.

Wind stow safety. When wind speed exceeds the safety threshold, the system drives the panels rapidly to a horizontal or otherwise protected stow position. Hydraulic actuation provides the force and speed needed to secure the entire installation in seconds, protecting the asset and reducing insurance risk.

Robustness and long service life. A sealed hydraulic circuit tolerates dust, vibration and temperature extremes far better than many electromechanical actuators. Fewer wear-sensitive components mean lower maintenance over a plant lifetime measured in decades.

Environmental compatibility. For installations in sensitive areas, biodegradable hydraulic fluids such as Matrol BI reduce environmental risk in case of leakage, an increasingly important factor in renewable energy projects.

From hydraulic power unit for solar tracking to smart power unit

A conventional hydraulic power unit HPU provides muscle. A Smart Power Unit adds the brain.

This is the key step that turns a hydraulic actuator into a complete, self-contained tracking subsystem.

The Smart Power Unit integrates an onboard electronic controller programmed in CoDeSys (IEC 61131-3) and communicating over CAN bus (SAE J1939). This architecture allows the unit to do far more than simply pump oil. It can acquire signals from sensors, run control algorithms, manage safety logic and exchange data with the plant SCADA, all from a single compact device installed close to the structure it moves.

Two functions are particularly relevant for solar tracking: sensor reading and position control.

Reading the panel sensors of the hydraulic suntracker with a programmable power unit

Each tracker needs to know where it is pointing and where the sun is. The Smart Power Unit acquires inputs from inclinometers, angle encoders, irradiance sensors or sun-position references, and uses them to calculate the required movement. Because the controller is onboard, this acquisition happens locally and in real time, with no need for a separate external PLC for each tracker. The result is faster response, simpler wiring and a more compact, reliable installation.

Closed-loop position control with the smart hydraulic power unit

The intelligence of the hydraulic power unit unit lies in its closed-loop control. The controller compares the measured angle from the sensors with the target angle calculated from the solar algorithm, then commands the hydraulic outputs to correct the difference. This enables smooth, accurate tracking throughout the day, automatic backtracking to avoid row-to-row shading in the early morning and late afternoon, and immediate transition to the wind stow position when required. The same control loop that maximizes daily energy harvest also protects the structure when conditions turn hostile.

One smart hydraulic power unit, up to six panels

Here is where the architecture becomes genuinely efficient. The power outputs of the Smart Power Unit drive the directional valves that feed the hydraulic cylinders on each panel or row. Because a single unit can pilot up to six double-acting valves, it can control six independent panels or sub-structures from one centralized device.

Each double-acting valve manages both directions of motion of its cylinder, so each of the six channels can move its panel forward and backward, in tracking and in stow. In practice this means:

  • One hydraulic Smart Power Unit serves a cluster of up to six panels or tracker sections.
  • Each panel is driven and positioned independently through its own double-acting valve.
  • Sensor reading and position control are managed centrally, with shared hydraulic power.

This consolidation reduces the number of power units, cylinders feeds and control nodes across the field, lowering installation cost, simplifying maintenance and shrinking the overall electrical and hydraulic footprint of the plant. For OEMs designing hydraulic power unit solar tracker systems, it is a direct path to a more competitive and scalable product.

Engineering specifications that matter for hydraulic solar tracking

For demanding outdoor applications, the hydraulic platform must be specified correctly. Hydronit designs compact hydraulic power units up to 370 bar with tank volumes from 0,4 to 30 litres, sized to deliver the force and duty cycle that large tracker structures require. The Hydronit’s Smart Power Unit is protected by European Patent EP3433434 and is built to functional safety standards, with capability up to SIL2 (IEC 61508) for applications where safe positioning and safe stow are critical.

Every unit is CE-marked and produced under an ISO 9001:2015 certified quality system, with marine certifications available for offshore and coastal projects. With 23 years of experience supplying OEMs in 70 countries, Hydronit combines proven hydraulic know-how with modern electronic control.

Hydronit’s smart power unit a cross-cutting solution

Solar tracking is a clear example of how compact hydraulics solves problems across very different industries, from waste handling and aerial work platforms to wind turbine braking and now renewable energy generation. The same building blocks, namely a compact HPU, intelligent CAN bus control and multi-valve actuation, are reused and adapted to each application. For hydraulic power unit for solar tracking specifically, this means more energy captured, structures protected in extreme weather, and a simpler architecture in which one Smart Power Unit can drive up to six panels with full sensor feedback and closed-loop position control.

Precision, force and reliability decide how much sun a plant can actually harvest. Hydraulics, made intelligent, delivers all three.

Do you want to know more about it? Contact our team.

Discover

Hydronit

Hydronit specializes in the production of modular hydraulic power packs. Innovation, quality and sustainability drive our solutions exported to over 50 countries.

12V Reversible Micro Hydraulic Power Unit Hydronit

Discover our range of Modular Hydraulic Power Packs